#Os xlog into user session how to
#Os xlog into user session software
#Os xlog into user session series

The IP address of the device is listed in In this case, port e1/2 was shut down and reenabled, and the following was Least one tab between the verity and the action Severity: notifications (level 5, the default) You do not want log messages to fill up the /įile system. They cannot be confused with other non-Cisco syslog messages. Messages are logged to a different file from the standard syslog file so that (lower number) will be acted upon as you configure the syslog server. Syslog server determines that all messages of that level and greater severity They could be logged to differentįiles or e-mailed to a particular user. Different message severitiesĪre handled differently by the syslog server. System in this example) and the message severity.

#Os xlog into user session how to

How to configure the device to use the syslog facility on a Solaris platform.Īlthough a Solaris host is being used, the syslog configuration on all UNIX andįacility to determine how to handle a message on the syslog server (the Solaris Period of time or if the device is not accessible. This feature allows you to examine the logs over a long PleaseĬontact your customer support representative for a list of authorizedĪllows the device to send a copy of the message log to a host for more Transceiver for interface is not supported.Įxplanation Transceiver (SFP) is not from anĬommand or similar DCNM command to determine the transceiver being used. The action may be as simpleĪs 'No action is required.' It might involve a fix or a recommendation toĬontact technical support as shown in the following example:Įrror Message PORT-3-IF_UNSUPPORTED_TRANSCEIVER: PORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver for interfaceįollowed by an explanation and recommended action. A decimal number, for example, is represented as. Because the information in these variable fields changesįrom message to message, it is represented here by short strings enclosed in Network addresses, or addresses that correspond to locations in the system This portion of the message mightĬontain detailed information about the event, including terminal port numbers, Some messages are purely informational, while others might helpĭiagnose problems with links, internal hardware, or the device software.Ī text string that describes the condition.

Not all messages indicate a problem with yourĭevice. Sends syslog (system) messages to the console (and, optionally, to a logging Protocol traces using SPAN or Ethanalyzer on the CLI.Īnd other diagnostic data for use by Cisco TAC or your customer support Issues and inoperable hardware components so that the problems are resolved

#Os xlog into user session software

Network, you should be able to diagnose and correct software configuration Symptoms in this publication to the symptoms that you observe in your own Problems by comparing the symptoms that you observed in your network with the Symptom-based troubleshooting approach that allows you to diagnose and resolve Questions to verify Layer 3 connectivity:Ĭonfigured the same dynamic routing protocol parameters throughout your routingĪccess lists, filters, or route maps blocking route updates?Ĭommands to verify your routing configuration: Nonessential Layer 2 processes are in the error state.ĭynamic vlan command to determine if learning or aging is occurring at each (STP) is configured the same on all devices in the network. Spanning-tree command to verify that the Spanning Tree Protocol The statusĬompatibility-parameters command to verify that all of the ports inĪ port channel are configured the same for the speed, the duplex, and the trunk Verify that all the necessary interfaces are in the same VLAN.

Questions to verify that your ports are connected correctly and areĬorrect media (copper, optical, fiber type)? The tools that are commonly used to troubleshoot problems within your network.Īccurate topology of your network to isolate problem areas. Physical connectivity between your device and end devices.Įnd-to-end connectivity and the routing configuration.ĭetermined that your troubleshooting attempts have not resolved the problem,Ĭontact Cisco TAC or your technical support representative. New configuration changes after implementing the change. Release for the latest features, limitations, and caveats.

Network, follow these general guidelines:

#Os xlog into user session series

This image runs on all Cisco Nexus 3400 Series switches. The Cisco NX-OS software consists of one NXOS software image.